New Holland Kenya

Discbine® 209

Cutting width ft. in. (m)	9’ 2” (2.8)
Number of discs	7
Type (Tongue Options)	Side-pull, straight tongue
Length, transport ft. in. (m)	Flail Tine: 18’ 1’’ (5.50)* or Roll: 17’ 7’’ (5.23)*

Discbine® 209
Standard Optional
Cutterbar
Cutting width ft. in. (m)	9’ 2” (2.8)
Cutterbar model	MowMax™ Modular Cutterbar with ShockPRO™ hubs
Number of discs	7
Knives per disc	2
Disc speed @ 540 rpm PTO speed rpm	3000
Tilt angle degrees	2° - 10°
Flotation	Up & back, adjustable springs
Drive method	PTO drive with slip & overrunning clutch to bevel gearbox to LH end of header, vertical PTO shaft to cutterbar
Cutting height in. (mm)	1.1-2.7 (29-68)
Cutting height w/optional high-stubble shoes in. (mm)	2.25-4.5 (58-115)
Cutting height w/optional adjustable shoes in. (mm)	2.25-4.5 (58-115)
Roll Conditioners
Type	Chevron intermeshing rubber
Length / Diameter in. (mm)	90 (2286) / 10.4 (264)
Drive method	4 HB V-belt and enclosed gears
Speed rpm	647
Conditioner roll tension adjustment	Single crank
Conditioner gap adjustment	Adjustable drawbolt stop, each end
LeaningEdge Flail Conditioners
Type	Flail rotor with 90 tapered flails
Length / Diameter in. (mm)	90 (2286) / 22 (560)
Drive method	4 HB v-belt
Speed rpm	718 std. 1000 opt.
Conditioner gap adjustment	Single crank adjustable rotor hood
Crop Discharge
Swath width ft. (m)	6 (1.83)
Windrow width ft. (m)	3-6 (0.9-1.83)
Driveline
Input speed rpm	540
Driveline protection	Slip clutch and overrunning clutch assembly at rear of PTO shaft
Secondary driveline	Non-CV driveline
Tongue Options
Type	Side-pull, straight tongue
Hitch type	Drawbar with CV PTO
Tractor Requirements
Minimum PTO power required hp (kW)	65 (49)
Hydraulic circuits required	2
Minimum relief pressure required psi (bar)	1500 (103)
Drawbar	ASAE Category II
Swivel Hitch - Drawbar	–
Swivel Hitch - 2-Point	–
Electrical	7-pin electrical connector for transport lights
Tires
Tubeless ag rib implement tires	9.5L x 14L 6PR
Transport Speed
Max road speed mph (kph)	20 (32)
Dimensions*
Width, transport ft. in. (m)	9’ 11” (3.02)
Width , operating ft. in. (m)	14’ 10” (4.52)
Length, transport ft. in. (m)	Flail Tine: 18’ 1’’ (5.50)* or Roll: 17’ 7’’ (5.23)*
Length, operating ft. in. (m)	Flail Tine: 17’ 8’’ (5.4)* or Roll: 17’ 2’’ (5.23)*
Height ft. in. (m)	Transport: 5’ 8” (1.73) / Operating: 4’ 5” (1.35)
Ground clearance with head fully raised in. (mm)	17 (4.32)
Weights**
Operating weight lbs. (kg.)	Flail Tine: 3690 (1674)* / Roll: 3740 (1697)*

Discbine® 210

Cutting width ft. in. (m)	10’ 4” (3.16)
Number of discs	8
Type (Tongue Options)	Side-pull, curved tongue
Length, transport ft. in. (m)	Flail Tine: 18’ 1’’ (5.50)* or Roll: 17’ 7’’ (5.23)*

Discbine® 210
Standard Optional
Cutterbar
Cutting width ft. in. (m)	10’ 4” (3.16)
Cutterbar model	MowMax™ Modular Cutterbar with ShockPRO™ hubs
Number of discs	8
Knives per disc	2
Disc speed @ 540 rpm PTO speed rpm	3000
Tilt angle degrees	2° - 10°
Flotation	Up & back, adjustable springs
Drive method	PTO drive with slip & overrunning clutch to bevel gearbox to LH end of header, vertical PTO shaft to cutterbar
Cutting height in. (mm)	Flail Tine: 1.1-2.7 (29-68) or Roll: .95-2.4 (24-60)
Cutting height w/optional high-stubble shoes in. (mm)	2.25-4.5 (58-115)
Cutting height w/optional adjustable shoes in. (mm)	2.25-4.5 (58-115)
Roll Conditioners
Type	Chevron intermeshing rubber or steel rolls
Length / Diameter in. (mm)	102 (2591) / 10.4 (264)
Drive method	4 HB V-belt and enclosed gears
Speed rpm	647
Conditioner roll tension adjustment	Single crank
Conditioner gap adjustment	Adjustable drawbolt stop, each end
LeaningEdge Flail Conditioners
Type	Flail rotor with 100 tapered flails
Length / Diameter in. (mm)	102 (2591) / 22 (560)
Drive method	4 HB v-belt
Speed rpm	718 std. 1000 opt.
Conditioner gap adjustment	Single crank adjustable rotor hood
Crop Discharge
Swath width ft. (m)	7 (2.13)
Windrow width ft. (m)	3-7 (0.9-2.13)
Driveline
Input speed rpm	540 or 1000 Standard Drawbar Attachment - 540 Only Swivel Hitch Attachment
Driveline protection	Slip clutch and overrunning clutch assembly at rear of PTO shaft
Secondary driveline	Double CV Driveline - Head repositionable under
Tongue Options
Type	Side-pull, curved tongue
Hitch type	Standard Drawbar with CV PTO - Swivel hitch with drawbar adapter or 2-point hitch
Tractor Requirements
Minimum PTO power required hp (kW)	80 (60)
Hydraulic circuits required	2
Minimum relief pressure required psi (bar)	1500 (103)
Drawbar	ASAE Category II
Swivel Hitch - Drawbar	ASAE Category II or III
Swivel Hitch - 2-Point	ASAE Category II, III-N, or III
Electrical	7-pin electrical connector for transport lights
Tires
Tubeless ag rib implement tires	Flail Tine: 9.5L x 14L 6PR / Roll: 11L x 15L 6 PR
Transport Speed
Max road speed mph (kph)	20 (32)
Dimensions*
Width, transport ft. in. (m)	11’ 3” (3.42)
Width , operating ft. in. (m)	16’ 0” (4.87) / 17’ 7’’ (5.36), with swivel hitch equipped
Length, transport ft. in. (m)	Flail Tine: 18’ 1’’ (5.50)* or Roll: 17’ 7’’ (5.23)*
Length, operating ft. in. (m)	Flail Tine: 17’ 8’’ (5.4)* or Roll: 15’ 7’’ (4.75)*
Height ft. in. (m)	Transport: 5’ 3” (1.60) / Operating: 4’ 5” (1.35)
Ground clearance with head fully raised in. (mm)	Flail Tine: 17 (4.32) or Roll: 18 (4.57)
Weights**
Operating weight lbs. (kg.)	Flail Tine: 4100 (1864)* / Roll: 4160 (1891)*

DISCBINE® SIDE-PULL DISC MOWER-CONDITIONERS

Features

FAST, SMOOTH CUTTING

MOWMAX™ DISC CUTTERBAR

QUICKMAX™ BLADE CHANGE SYSTEM IS STANDARD EQUIPMENT

HIGH QUALITY AND FAST DRYDOWN

Gallery

MODELS

Discbine® 209

Discbine® 210