Specifications

Standard Optional
Cutterbar
 
Cutting width ft. in. (m)
Cutterbar model
Type
Number of discs
Knives per disc
Disc speed @ 1000 rpm PTO speed rpm
Tilt angle degrees
Flotation
Drive method
Cutting height in. (mm)
Cutting height w/ opt. high-stubble shoes in. (mm)
Cutting height w/ opt. Biomass shoes in. (mm)
Cutting height w/ opt. adjustable shoes in. (mm)
Discbine® 313Discbine® 316
13’ 0” (4.0)16’ 3” (4.95)
MowMax™ II with ShockPRO™ hubsMowMax™ II with ShockPRO™ hubs
ModularModular
810
22
2,2502,250
2-102-10
Vertical and lateral, adjustable springsVertical and lateral, adjustable springs
PTO drive w/slip clutch to bevel gearbox to LH end of header, vertical PTO shaft to cutterbarPTO drive w/slip clutch to bevel gearbox to LH end of header, vertical PTO shaft to cutterbar
0.79-2.7 (20-69)0.79-2.7 (20-69)
3.1-5.5 (79-140)3.1-5.5 (79-140)
4.9-7.8 (124-198)4.9-7.8 (124-198)
0.79-5.8 (20-147)0.79-5.8 (20-147)
Roll Conditioners
 
Type
Length in. (mm)
Diameter in. (mm)
Drive method
Speed rpm
Conditioner roll tension adjustment
Conditioner gap adjustment
Discbine® 313Discbine® 316
Chevron intermeshing rubber or steel rollsChevron intermeshing rubber or steel rolls
125 (3175)125 (3175)
10.4 (264)10.4 (264)
4 HB V-belt and enclosed gears4 HB V-belt and enclosed gears
750 or 640750 or 640
Single crankSingle crank
Adjustable drawbolt stop, each endAdjustable drawbolt stop, each end
LeaningEdge Flail Conditioners
 
Type
Length in. (mm)
Diameter in. (mm)
Drive method
Speed rpm
Conditioner gap adjustment
Discbine® 313Discbine® 316
Flail rotor with 120 tapered flails
125 (3175)
22 (560)
4 HB v-belt
1042 std. 752 opt.
Single crank adjustable rotor hood
Crop Discharge
 
Swath width ft. (m)
Windrow width ft. (m)
Discbine® 313Discbine® 316
10 (3.0)10 (3.0)
3-8 (0.9-2.4)3-8 (0.9-2.4)
Driveline
 
Input speed rpm
Driveline protection
Discbine® 313Discbine® 316
10001000
Slip clutch and overrunning clutch assembly at rear of PTO shaftSlip clutch and overrunning clutch assembly at rear of PTO shaft
Tongue Options
 
Tongue type
Hitch type
Discbine® 313Discbine® 316
Center pivot straight hitchCenter pivot straight hitch
Drawbar swivel or 2-point swivelDrawbar swivel or 2-point swivel
Tractor Requirements
 
Minimum PTO power required hp (kW)
Hydraulic circuits required
Minimum relief pressure required psi (bar)
Drawbar
3 pt hitch (swivel models)
Electrical
Discbine® 313Discbine® 316
90 (67)100 (75)
22
1,500 (103)1,500 (103)
ASAE Category II or IIIASAE Category III
Category IIICategory III
7-pin electrical connector for transport lights7-pin electrical connector for transport lights
Tires
 
Tubeless ag rib implement tires
Discbine® 313Discbine® 316
12.5L x 15 8PR12.5L x 15 8PR
Transport Speed
 
Max road speed mph (kph)
Discbine® 313Discbine® 316
20 (32)20 (32)
Dimensions
 
Width-transport ft. in. (m)
Width-operating (2 pt swivel hitch) ft. in. (m)
Width-operating (drawbar swivel hitch)
Length-transport (2 pt swivel hitch) ft. in. (m)
Length-transport (drawbar swivel hitch)
Length-operating (2pt swivel hitch) ft. in. (m)
Length-operating (drawbar swivel hitch)
Height-transport ft. in. (m)
Height-operating ft. in. (m)
Ground clearance with head fully raised in. (mm)
Discbine® 313Discbine® 316
13’ 4” (4.04)16’ 7” (5.05)
21’ 3” (6.5)25’ 7” (7.8)
19’ 7” (6.0)23’ 11” (7.3)
27’ 5” (8.4)32’ 0” (9.7)
26’ 5” (8.1)31’ 0” (9.4)
23’ 0” (7.0)26’ 7” (8.1)
22’ 0” (6.7)25’ 7” (7.8)
7’ 5” (2.26)7’ 5” (2.26)
6’ 7” (2.01)6’ 7” (2.01)
16.2 (411)16.2 (411)
Weights**
 
Operating weight
Discbine® 313Discbine® 316
6,275 (2846)6,700 (3039)

Standard Optional – Not Available
*Rear curtain down for all height and length measurements on machines with flail conditioners. Subtract 2” (50.8 mm) for flail curtain up. Windrow shields fully open for length in both positions.
**Weights with rubber conditioning rolls. Add 100 lbs. (45 kg) for steel rolls.



New Holland & CMC Motors Group ©
back to top